Compaq HSG80 - StorageWorks RAID Array Controller Specifikace Strana 241
- Strana / 396
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
7–45
Compaq HSG80 Array Controller ACS Version 8.4 Configuration and CLI Reference Guide
CONFIGURATION RESTORE
Copies a controller’s configuration from the disk configuration file into the
controller’s non-volatile memory. This command locates the most recent
configuration file created on disk and restores it. This command causes a reboot and
takes effect immediately.
Use this command for a single controller configuration only. Do not use it for
controllers in a dual-redundant configuration.
You can also initiate the CONFIGURATION RESTORE command from the
controller’s operator control panel (OCP) by holding in port button 6 and pressing the
reset button.
NOTE: The controller must not have devices configured prior to issuing this
command. Use “CONFIGURATION RESET,” page 7–44, instead.
If the controller you’re installing was previously used in another subsystem, it will
restart with the configuration that resides in its nonvolatile memory. If this differs
from the subsystem’s current configuration, you can purge the controller’s old
configuration with the following command:
configuration RESET
This will erase the entire configuration on the controller, restore the controller’s
default configuration, and shut down the controller. Press its reset button to restart the
controller after the controller has been configured. See Chapter 5, “Configuring an
HSG80 Array Controller.”
NOTE: The INITIALIZE container-name SAVE_CONFIGURATION must be used to
save the controller’s configuration to a disk (see “SAVE_CONFIGURATION,”
page 7–64), in order to reset the configuration (see “CONFIGURATION RESET,”
page 7–44) or to restore the configuration (see “CONFIGURATION RESTORE,”
page 7–45).
- First Edition (April, 1999) 1
- Compaq Computer Corporation 1
- Contents 3
- Chapter 2 4
- Chapter 3 4
- Chapter 4 5
- Chapter 5 6
- Chapter 6 7
- Chapter 7 8
- System Profiles 10
- Controller Specifications 10
- Glossary 10
- About This Guide 15
- Precautions 16
- Maintenance Port Precautions 17
- FCC Precautions 17
- Conventions 18
- Typographical Conventions 19
- Special Notices 20
- Related Publications 21
- About This Guide 22
- Revision History 23
- General Description 25
- General Description 26
- CXO6841A 27
- Summary of HSG80 Features 29
- Controller Components 32
- Cabling (Continued) 33
- Operator Control Panel 35
- Maintenance Port 36
- Utilities and Exercisers 36
- Virtual Terminal Display 37
- Disk Inline Exerciser 37
- Configuration Utility 37
- Clone Utility 38
- Field Replacement Utility 38
- Device Statistics Utility 38
- Cache Module 39
- External Cache Battery 41
- Charging Diagnostics 42
- Battery Hysteresis 43
- Controller and Host Concepts 45
- Terminology 46
- Item Description 47
- ➀ Other controller 47
- ➁ This controller 47
- Selecting a Failover Mode 49
- Shared Port IDs 50
- Separate Port IDs 51
- Preferring the Host Path 52
- Caching Techniques 53
- Write-Through Caching 54
- Write-Back Caching 54
- Nonvolatile Memory 55
- Chapter 3 63
- Bus Dynamics 64
- Host Bus 65
- Controller Device Bus 65
- Containers and Storagesets 66
- Containers 67
- Addressing 68
- Disk 10000 71
- Disk 20000 Disk 30000 71
- Failover Mode 72
- CXO6454B 74
- Assigning Unit Offsets 75
- Assigning Access Paths 76
- (Node IDs) 77
- Planning Storagesets 81
- Disk drives 83
- Choosing a Storageset Type 88
- CXO5507A 89
- ➀ First member of Mirrorset 1 95
- ➁ First member of Mirrorset 2 95
- Availability 96
- I/O Request 97
- Performance and Availability 99
- Stripeset 100
- Cloning Data for Backup 101
- Planning Storagesets 102
- SAVE_CONFIGURATION 107
- INITIALIZE 107
- INITIALIZE DISK 107
- Creating a Storageset Map 110
- Spare spare Spare R1 111
- R2 R2 R2 R2 111
- Spare Spare Spare Spare 111
- M1 M1 M2 M2 111
- Planning Partitions 114
- Disk Drives 115
- Enabling Switches 116
- Changing Switches 116
- RAIDset Switches 117
- Membership 118
- Mirrorset Switches 119
- Read Source 120
- Device Switches 121
- Device Transfer Rate 122
- Initialize Switches 123
- Increasing the Request Rate 124
- CXO-5172A-MC 125
- Save Configuration 126
- Configurations 128
- Destroy/Nodestroy 129
- Chapter 5 131
- Introduction 133
- Controller 134
- Maintenance and Service Guide 136
- RUN FRUTIL 137
- SHOW THIS_CONTROLLER FULL 137
- Using Two Switches 138
- Switches 138
- Using One Switch 140
- IDENTIFIER 151
- Optional Steps 159
- Extended Subsystem 160
- Setting a Port Offline 161
- Backing Up Power with a UPS 161
- CXO6476B 164
- Shutting Down Your Subsystem 166
- Restarting Your Subsystem 167
- Configuring Storagesets 169
- Unit Switches 170
- Adding Disk Drives 171
- Formatting Disk Drives 171
- Configuring Storagesets 172
- Configuring a Stripeset 174
- Configuring a Mirrorset 175
- Configuring a RAIDset 176
- RAIDset-name switch 177
- RAIDset-name 177
- Enabling Autospare 185
- Deleting a Storageset 186
- Changing Device Switches 187
- Changing Initialize Switches 188
- Changing Unit Switches 188
- Finding the CCL Location 190
- SCSI-2 and SCSI-3 Modes 190
- Multiple-Bus Failover 191
- Transparent Failover 191
- SCSI-2 Mode 192
- SCSI-3 Mode 192
- Moving Storagesets 193
- Name Storageset Uses Used by 195
- CLI Commands 197
- CLI Overview 198
- Command Overview 199
- Getting Help 199
- Entering CLI Commands 200
- Changing the CLI Prompt 201
- Command Syntax 201
- ADD CONNECTIONS 202
- CLI Commands 204
- Examples 205
- See also 205
- ADD DISK 206
- ADD MIRRORSET 209
- ADD RAIDSET 213
- ADD REMOTE_COPY_SETS 217
- ADD SPARESET 219
- ADD STRIPESET 220
- ADD UNIT 223
- CLEAR_ERRORS CLI 231
- CLEAR_ERRORS 232
- INVALID_CACHE 232
- UNKNOWN 235
- LOST_DATA 236
- UNWRITEABLE_DATA 238
- CONFIGURATION RESET 240
- CONFIGURATION RESTORE 241
- CONFIGURATION SAVE 243
- CREATE_PARTITION 244
- Parameters 247
- DELETE FAILEDSET 251
- DELETE SPARESET 252
- Parameter 253
- DESTROY_PARTITION 254
- DIRECTORY 256
- LOCATE D102 265
- LOCATE DISKS 265
- LOCATE CANCEL 265
- POWEROFF 270
- RESTART 277
- RETRY_ERRORS UNWRITEABLE_DATA 279
- SELFTEST 283
- Table 7–4. SET 288
- Switches 288
- Switches (Continued) 289
- SET FAILEDSET 302
- SET FAILOVER 304
- SET MULTIBUS_FAILOVER 311
- SET NOFAILOVER 313
- SET NOMULTIBUS_FAILOVER 315
- Table 7–6 SET 323
- SHOW MIRR1 333
- EMU CABINET SETTINGS 335
- FANSPEED AUTOMATIC 335
- SHUTDOWN 336
- UNMIRROR 338
- Device Profile 340
- Storageset Profile 341
- Enclosure Template 342
- Environmental Specifications 345
- B–4 Controller Specifications 346
- GL–2 Glossary 348
- See also 349
- GL–4 Glossary 350
- GL–6 Glossary 352
- GL–8 Glossary 354
- GL–10 Glossary 356
- GL–12 Glossary 358
- GL–14 Glossary 360
- GL–16 Glossary 362
- GL–18 Glossary 364
- GL–20 Glossary 366
- GL–22 Glossary 368
- GL–24 Glossary 370
Související produkty a manuály pro Síťové přepínače Compaq HSG80 - StorageWorks RAID Array Controller
Síťové přepínače Compaq HB1004 Uživatelská příručka
(45 stránky)
(45 stránky)
(19 stránky)Corsair CO-9050009-WW Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Komponenten für die Computerkühlung Corsair CO-9050009-WW.
Wir stellen 1 PDF-Handbücher Corsair CO-9050009-WW zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Datenblatt
Corsair CO-9050009-WW Datenblatt (2 Seiten)
Marke: Corsair | Kategorie: Computer cooling components | Größe: 0.31 MB |
Inhaltsverzeichnis
Weitere Produkte und Handbücher für Komponenten für die Computerkühlung Corsair
| Modelle | Dokumententyp |
|---|---|
| CO-9050002-WW |
Datenblatt
Corsair AF120 Quiet Edition Single Pack,
2 Seiten
|
| CO-9050006-WW |
Datenblatt
Corsair SP120 Quiet Edition Single Pack,
2 Seiten
|
| CW-9060014-WW |
Datenblatt
Corsair Hydro H110,
2 Seiten
|
| CAFA70 |
Datenblatt
Corsair A70,
3 Seiten
|
| CWCH70 |
Datenblatt
Corsair CWCH70,
2 Seiten
|
| CMDAF |
Handbuch
  
Corsair CMDAF,
1 Seiten
|
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.059 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce