Compaq OXYGEN VX1 Uživatelský manuál Strana 1

3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide Order Number: EK-VX1GC-IG. A01 This guide describes the installation of the 3Dlabs O

1-4 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide 1.4 Specifications Table 1–3 lists the specifications for the 3Dlabs OXYGEN VX1

Installation 2-1 Chapter 2 Installation 2.1 Introduction This chapter describes the installation of the 3Dlabs OXYGEN VX1 PCI graphics controller m

2-2 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide 2.3 Installation Procedure The following section describes how to install the 3Dl

Installation 2-3 7. Grasp the top edge of the graphics option, carefully insert it into the slot, and seat it firmly. 8. Secure the module with t

Compaq Tru64 UNIX Configuration 3-1 Chapter 3 Compaq Tru64 UNIX Configuration This chapter describes how to configure the 3Dlabs OXYGEN VX1 PCI gra

3-2 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide 3.2 Restrictions and Limitations This section of the document contains limitations

Compaq Tru64 UNIX Configuration 3-3 3.2.4 Backing Store and Save Unders By default, backing store and save unders are enabled. If the default visu

3-4 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide 3.3.3 How to Determine which GUI is in Use 1. Check the environment variable XLOG

Compaq Tru64 UNIX Configuration 3-5 ___________________________Note ____________________________ • These are device dependent X server options an

© 2000 Compaq Computer Corporation Compaq, the Compaq logo, Compaq Insight Manager, AlphaServer, StorageWorks, and TruCluster Registered in U.S. Paten

3-6 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide 4. Edit the file /etc/dt/config/Xservers and add the appropriate X server Option,

Compaq Tru64 UNIX Configuration 3-7 • Setting the Screen Resolution to 1280 x 1024 and the Vertical Refresh Rate to 75Hz. :0 Local local@console

3-8 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide 3.4.2 Matching X Server Primary Screen with VGA Console PCI slots are not always

Compaq OpenVMS Software Installation and Customization 4-1 Chapter 4 Compaq OpenVMS Software Installation and Customization This chapter provides

4-2 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide Table 4-1 OpenVMS Version Supporting 3Dlabs OXYGEN VX1 PCI Graphics Controller Op

Compaq OpenVMS Software Installation and Customization 4-3 latest GRAPHICS kit, if required. View the Readme files for each kit to determine if the

4-4 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide 4.4 Default Graphics Settings The default graphics resolution is 1024 x 768. Th

Compaq OpenVMS Software Installation and Customization 4-5 3. For the changes to take effect immediately you must restart the X server so that the

4-6 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide number of slots available and the number of heads (graphics modules) qualified for

Compaq OpenVMS Software Installation and Customization 4-7 4.9 POLYCENTER Software Installation At the end of the OpenVMS POLYCENTER Software Inst

iii Contents Preface...v Chap

iv Chapter 4 Compaq OpenVMS Software Installation and Customization 4.1 Installation Preparation...

v Preface Intended Audience This manual is for owners installing the 3Dlabs OXYGEN VX1 PCI graphics controller in supported Compaq products. Document

vi Conventions Used in This Guide In this guide, every use of Tru64 UNIX refers to Compaq’s Tru64 UNIX and DIGITAL UNIX operating systems. Every use

Overview 1-1 Chapter 1 Overview 1.1 Introduction This chapter provides a brief overview of the 3Dlabs OXYGEN VX1 PCI graphics controller. 1.2 Mo

1-2 3Dlabs OXYGEN VX1 PCI Graphics Controller Installation Guide Figure 1– 1 3Dlabs OXYGEN VX1 PCI Graphics Controller PK3213 The 3Dlabs OXYGE

Overview 1-3 1.3 Connector Pinouts Table 1–2 contains a listing of the pins and signals found on the standard 15-pin VGA connector. Table 1– 2