Compaq Wireless LAN 100 Technické informace

HP Mini 1000 NetbookCompaq Mini 700 NetbookMaintenance and Service Guide

Category Description HP Mini 1000NetbookCompaq Mini 700NetbookMass storage devices Solid-state drive (SSD) based on multi-level cell(MLC) technologyCo

Where used: One screw that secures the top cover to the deviceWhere used: One screw that secures the fan and DC jack bracket to the base enclosureWher

Where used: Four screws that secure the display hinges to the display assemblyPhillips PM2.5×5.0 screwColor Quantity Length Thread Head diameterSilver

Phillips PM2.5×7.0 screwColor Quantity Length Thread Head diameterBlack 4 7.0 mm 2.5 mm 4.0 mmWhere used: Four screws that secure the top cover to the

8 Backup and recoveryBacking up your informationNOTE: You can recover only the files that you have previously backed up. HP recommends that youuse the

Backup suggestions●Connect the device to external power before performing backup and recovery procedures.●Create system recovery points.●Store persona

Backing up all files and foldersWhen you back up all files and folders, you are saving all personal files and folders, all system files, andconfigurat

Scheduling backupsYou can schedule backups for the entire system, for recovery points, or for specific files and folders.Backups can be scheduled at s

9 Connector pin assignmentsAudio-in (microphone)Pin Signal1 Audio signal in2 Audio signal in3GroundAudio-out (headphone)Pin Signal1 Audio out, left ch

RJ-45 (network)Pin Signal1 Transmit +2 Transmit -3 Receive +4 Unused5 Unused6 Receive -7 Unused8 UnusedUniversal Serial BusPin Signal1 +5 VDC2 Data -3

10 Power cord set requirementsThe wide range input feature of the device permits it to operate from any line voltage from 100 to 120volts AC or from 2

Category Description HP Mini 1000NetbookCompaq Mini 700NetbookDocking Expansion portSignals passed through expansion port:●USB 2.0●Headphone-out/stere

Requirements for specific countries and regionsCountry/region Accredited agency Applicable note numberAustralia EANSW 1Austria OVE 1Belgium CEBC 1Cana

11 RecyclingBatteryWhen a battery has reached the end of its useful life, do not dispose of the battery in general householdwaste. Follow the local la

Perform the following steps to disassemble the display assembly:1. Remove all screw covers (1) and screws (2) that secure the display bezel to the dis

4. Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).5. Remove all screws (1) that secure the display pane

10. Remove the display panel frame (2) from the display panel.11. Remove the screws (1) that secure the backlight cover to the display panel.12. Lift

15. Remove the backlight cables (1) from the clip (2) in the display panel.16. Turn the display panel upside down.WARNING! The backlight contains merc

18. Remove the backlight from the backlight frame.19. Disconnect the display panel cable (1) from the LCD panel.20. Remove the screws (2) that secure

IndexAAC adapter, spare partnumber 23, 24antennalocations 5removal 69spare part number 18, 69audio, product description 2audio-in jacklocation 10pin

foil shield, spare part number 18, 26, 28front components 8function keys 6Ggraphics, product description 1grounding equipment andmethods 33Hhard driv

product descriptionaudio 2chipset 1diskette drive 2Ethernet 2expansion port 3external media cards 2flash storage drive 2graphics 1hard drive 2internal

2 External component identificationTop componentsDisplayItem Component Function(1) Internal display switch Turns off the display if the display is clo

Windows applications key 6Windows logo key 6wireless antennalocations 5removal 69spare part number 18, 69wireless antenna components 5wireless light

Wireless antennaeItem Component Function(1) WLAN antennae (2) * Send and receive wireless signals to communicate withwireless local-area networks (WLA

KeysItem Component Function(1) esc key Displays system information when pressed in combinationwith the fn key.(2) Function keys Execute frequently use

TouchPadItem Component Function(1) TouchPad on/off button Turns the TouchPad on and off.(2) TouchPad on/off light●White: TouchPad is on.●Amber: TouchP

Front componentsItem Component Function(1) Power light●On: The device is on.●Blinking: The device is in Standby.●Off: The device is off.(2) Power swit

Right-side componentsItem Component Function(1) Vent Enables airflow to cool internal componentsNOTE: The device fan starts up automatically to coolin

Left-side componentsItem Component Function(1) Power connector Connects an AC adapter.(2) Power connector light●On: The device is running on AC power.

Bottom componentsItem Component Function(1) Battery bay Holds the battery.(2) Battery release latches (2) Release the battery from the battery bay.(3)

© Copyright 2008 Hewlett-PackardDevelopment Company, L.P.Bluetooth is a trademark owned by itsproprietor and used by Hewlett-PackardCompany under lice

3 Illustrated parts catalogSerial number locationThe service tag, affixed to the bottom of the device, provides information that may be needed whentro

Device major componentsItem Description Spare part number(1) Display assembly (includes 1 webcam, 1 microphone, 1 speaker box, and 2 WLAN antennatrans

Item Description Spare part number 10.2-inch WSVGA AntiGlare (red-colored HP Mini 1000) 512140-001 10.2-inch WSVGA AntiGlare (Compaq Mini 700) 51214

Item Description Spare part number For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,Armenia, Aruba, Australi

Item Description Spare part number(16) Battery (3-cell, 26-Wh Li-Pol) For the HP Mini 1000 and Compaq Mini 700 504610-001 For the red-colored HP M

Display assembly componentsNOTE: 10.1-inch display assembly components are not sold separately for the HP Mini 1000. Thecomplete display assembly is a

Item Description Spare part number(4) Webcam module NOTE: The webcam module spare part kit does not include a webcam cable. Anintegrated display/webca

Cable KitItem Description Spare part number Cable Kit: 507708-001(1) SIM card cable (2) Power cable (3) Internal display switch module (4) Bluetoo

Mass storage devicesNOTE: Each hard drive spare part kit and solid-state drive spare part kit includes a cable and bracket.Item Description Spare part

Plastics KitItem Description Spare part number Plastics Kit: For the HP Mini 1000 and Compaq Mini 700 507317-001 For the red-colored HP Mini 1000

Safety warning noticeWARNING! To reduce the possibility of heat-related injuries or of overheating the device, do not placethe device directly on your

Miscellaneous partsDescription Spare part numberBracket Kit●Actuators for power switch and wireless switch●DC jack bracket (fits over power and USB po

Description Spare part numberScrew Kit●Phillips PM1.6×2.5 screw●Phillips PM1.6×4.0 screw●Phillips PM1.6×6.0 screw●Phillips PM2.0×3.0 screw●Phillips PM

Sequential part number listingSpare partnumberDescription483377-002 HP un2400 Mobile Broadband Module490371-001 Power cord for use in North America (H

Spare partnumberDescription504594-001 Webcam module for use with all 8.9-inch panelsNOTE: The webcam module spare part kit does not include a webcam c

Spare partnumberDescription506333-001 Display bezel for use with 8.9-inch panels on the HP Mini 1000506334-001 Foil shield for use with all 8.9-inch d

Spare partnumberDescription509650-291 Keyboard for use in Japan (red-colored HP Mini 1000 only)509650-AB1 Keyboard for use in Taiwan (red-colored HP M

Spare partnumberDescription515208-001 Display Cable Kit with WLAN for use with 10.1-inch panels on the Compaq Mini 700 (includes microphoneassembly an

4 Removal and replacement proceduresPreliminary replacement requirementsTools requiredYou will need the following tools to complete the removal and re

Drive handlingCAUTION: Drives are fragile components that must be handled with care. To prevent damage to thedevice, damage to a drive, or loss of inf

Grounding guidelinesElectrostatic discharge damageElectronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure

iv Safety warning notice

Packaging and transporting guidelinesFollow these grounding guidelines when packaging and transporting equipment:●To avoid hand contact, transport pro

Equipment guidelinesGrounding equipment must include either a wrist strap or a foot strap at a grounded workstation.●When seated, wear a wrist strap c

Unknown user passwordIf the device you are servicing has an unknown user password, follow these steps to clear the password:NOTE: These steps also cle

Component replacement proceduresThis chapter provides removal and replacement procedures.There are as many as 49 screws, in 7 different sizes, that mu

Device feetThe device feet are adhesive-backed rubber pads. The feet are included in the Rubber Kit, spare partnumber 504613-001. There are 4 rubber f

BatteryDescription Spare part number3-cell, 26-Wh Li-Pol battery for the HP Mini 1000 and Compaq Mini 700 504610-0013-cell, 26-Wh Li-Pol battery for t

Memory moduleDescription Spare part number512-MB (PC2-4200, 533-MHz, DDR2) 504599-0011024-MB (PC2-4200, 533-MHz, DDR2) 504600-0012048-MB (PC2-4200, 53

4. Remove the memory module (2) by pulling the module away from the slot at an angle.NOTE: Memory modules are designed with a notch (3) to prevent inc

KeyboardNOTE: For a comprehensive list of spare part numbers, see the Sequential part number listingon page 24.Description Spare part number Descripti

4. Grasp the tabs (1) on the outer edges of the keyboard and lift the rear edge (2) until the keyboardrests at an angle. Then slide the keyboard back

Table of contents1 Product description2 External component identificationTop components ...

Mass storage devicesNOTE: Each hard drive spare part kit and solid-state drive spare part kit includes a cable and bracket.Description Spare part numb

6. Lift the hard drive (4) up and slide it out of the drive bay.Reverse this procedure to install the hard drive.To remove the solid-state drive:1. Re

6. Remove the drive bracket (4) from the drive bay.7. Remove the three Phillips PM2.0×3.0 screws (1) that secure the solid-state drive to the bracket.

Top coverDescription Spare part numberTop cover (includes TouchPad) 504612-001Before removing the top cover, follow these steps:1. Shut down the devic

5. Open the device as far as possible.6. Remove the Phillips PM2.0×4.5 screw (1) and the Phillips PM2.5×5.0 screw (2) that secure the topcover to the

9. Disconnect the TouchPad button board cable (2) from the system board, and then remove the topcover.Reverse this procedure to install the top cover.

WLAN moduleDescription Spare part numberBroadcom 4312 802.11/b/g WLAN module for use in Canada, the Cayman Islands, Guam,Puerto Rico, the U.S. Virgin

Remove the WLAN module:1. Detach the black Mylar covering (not illustrated) that surrounds the fan.2. Several system cables are routed through a chann

WWAN moduleDescription Spare part numberHP un2400 Mobile Broadband Module 483377-002CAUTION: The WWAN module and the WLAN module are not interchangeab

Remove the WWAN module:1. Detach the black Mylar covering from the WWAN module. The covering is secured by adhesive.2. Detach the aluminum foil and ta

Workstation guidelines ... 32Equipment guidelines ...

RTC batteryDescription Spare part numberRTC battery 507707-001NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes a

Bluetooth moduleNOTE: The Bluetooth module spare part kit does not include a Bluetooth module cable. The Bluetoothmodule cable is included in the Cabl

System boardNOTE: The system board spare part kit includes a processor and replacement thermal material.Description Spare part numberSystem board equi

3. Disconnect the following cables from the system board:(1) Speaker cables(2) Microphone cable(3) Fan cable(4) Power cable(5) Display panel cable4. R

7. Remove the USB connector bracket (2).NOTE: The USB connector bracket is included in the Bracket Kit, spare part number 507318-001.8. Remove the Phi

9. Grasp the system board at its midpoint (1) and lift the right side (2) up. Then remove the systemboard (3) from the base enclosure.Reverse the proc

2. Remove the heat sink assembly (2).NOTE: Due to the adhesive quality of the thermal material located between the heat sinkassembly and system board

FanDescription Spare part numberFan 504615-001NOTE: To properly ventilate the device, allow at least a 7.6-cm (3-inch) clearance on the left side ofth

3. Remove the fan (3).Reverse this procedure to install the fan.60 Chapter 4 Removal and replacement procedures

USB board and internal display switchNOTE: The internal display switch module is included in the Cable Kit, spare part number 507708-001.Description S

System interrupt specifications ... 80System I

4. Detach the SIM card cable (3). The SIM card cable is attached to the battery bay with tape.Reverse this procedure to install the USB board.If it is

Display assemblyNOTE: Each display assembly spare part kit includes 1 webcam, 1 microphone, 1 speaker box, and2 WLAN antenna transceivers/cables; WWAN

2. Remove the display assembly (2).3. If it is necessary to replace the speaker assembly, perform the following steps:a. Squeeze the sides of the spea

c. Remove the speaker assembly (2). The speaker assembly is available as spare part number506335-001.4. If it is necessary to replace the display hing

b. Remove the display bezel (4). The spare part numbers for the 8.9-inch display bezels are506333-001 (HP Mini 1000) and 509701-001 (Compaq Mini 700).

d. Remove the two Phillips PM2.0×3.0 screws (1) that secure the webcam module to the displayenclosure.e. Remove the webcam module (2). The webcam modu

c. Remove the display panel (3) from the display enclosure. An 8.9-inch display panel for theHP Mini 1000 and the Compaq Mini 700 is available as spar

9. If it is necessary to replace the wireless antenna transceivers and cables, detach the cables fromthe adhesive that secures them to the display enc

5 Setup UtilityStarting the Setup UtilityThe Setup Utility is a ROM-based information and customization utility that can be used even when yourWindows

Navigating and selecting in the Setup UtilityBecause the Setup Utility is not Windows based, it does not support the TouchPad. Navigation andselection

viii

Exiting the Setup UtilityYou can exit the Setup Utility with or without saving changes.●To exit the Setup Utility and save your changes from the curre

System Configuration menuSelect To do thisLanguage Support Change the Setup Utility language.Processor C4 State Enable/disable the processor C4 sleep

6 SpecificationsDevice specifications Metric U.S.DimensionsDepth16.67 cm 6.56 inWidth 26.17 cm 10.30 inHeight 2.52 cm 0.99 inWeight10.2-in. LCD, equi

8.9-inch, WSVGA, BrightView display specifications Metric U.S.DimensionsHeight11.34 cm 4.47 inWidth 19.51 cm 7.68 inDiagonal 22.61 cm 8.90 inNumber o

10.1-inch, standard-definition, AntiGlare displayspecifications Metric U.S.DimensionsHeight23.45 cm 9.23 inWidth 14.30 cm 5.62 inDiagonal 25.55 cm 10

10.2-inch, WSVGA, AntiGlare display specifications Metric U.S.DimensionsHeight12.53 cm 4.93 inWidth 22.27 cm 8.77 inDiagonal 25.55 cm 10.06 inNumber

Hard drive specifications 60-GB *DimensionsHeight9.5 mmWidth 70 mmWeight 101 gInterface type PATATransfer rate 100 MB/secSecurity ATA securitySeek ti

Solid-state drive specificationsPerformanceTransfer modes supportedUDMA 0-4, Multiword-DMA 0-2, PIO 0-4Sustained read 39 MB/secSustained write 17 MB/s

System DMA specificationsHardware DMA System functionDMA0 Not applicableDMA1 * Not applicableDMA2 * Not applicableDMA3 Not applicableDMA4 Direct memor

System I/O address specificationsI/O address (hex) System function (shipping configuration)000 - 00F DMA controller000 - CF7 PCI bus010 - 01F Motherbo

1 Product descriptionCategory Description HP Mini 1000NetbookCompaq Mini 700NetbookProduct Name HP Mini 1000 Netbook √ Compaq Mini 700 Netbook √P

I/O address (hex) System function (shipping configuration)279 - 279 ISAPNP Read Data Port3B0 - 3BB Mobile Intel® 945 Express Chipset Family3C0 - 3DF M

System memory map specificationsMemory address System function00000000 - 0009FFFF System board000A0000 - 000BFFFF Mobile Intel® 945 Express Chipset Fa

7 Screw listingThis section provides specification and reference information for the screws and screw locks used inthe device. All screws listed in th

Where used: Two screws that secure the heat sink to the system boardPhillips PM1.6×4.0 screwColor Quantity Length Thread Head diameterSilver 1 4.0 mm

Phillips PM1.6×6.0 screwColor Quantity Length Thread Head diameterBlack 1 6.0 mm 1.60 mm 3.5 mmWhere used: One screw that secures the keyboard to the

Phillips PM2.0×3.0 screwColor Quantity Length Thread Head diameterBlack 24 (WLAN only)25 (with WWAN)3.0 mm 2.0 mm 4.0 mmWhere used: Three screws that

Where used: One screw that secures the WWAN connector bracket to the system boardWhere used: Two screws that secure the USB connector bracket to the s

Where used: One screw that secures the DC jack bracket to the base enclosureWhere used: One screw that secures the internal display switch bracket to

Where used: Nine screws that secure the display panel to the display enclosureWhere used: Four screws that secure the left and right display panel bra

Phillips PM2.0×4.5 screwColor Quantity Length Thread Head diameterSilver 10 4.5 mm 2.0 mm 4.0 mmWhere used: Two screws that secure the hard drive to t